vibration analysis
Webinars
Deciding Between Balance, Replace, or Align
Learn when alignment is truly the right corrective action in this webinar, where we’ll break down behavioral indicators, operational clues, and reliability patterns that help separate misalignment from overlapping vibration conditions, giving your team greater confidence in recommending alignment and showing how laser alignment delivers the precision needed to address the root cause.
- Terry Southall
- Hamar Laser Instruments, Inc.
Case Studies and Stories
Turning Early Detection into 9,300 Tons of Saved Production
A subtle change in vibration was the only early warning, but it was enough to make a major difference. By acting on advanced diagnostics and continuous condition monitoring, a fertilizer plant in France avoided unplanned downtime and saved 9,300 tons of production. This case study shows how early detection, paired with expert analysis, turns potential failure into operational advantage.
- Nicolas Bourdier, Khalid Achtal, Miguel Fernandez Sanz, Peter Popaleny
- Baker Hughes
Two Minute Tips
The Diagnostic Process
Tony Planamento from AME Solutions discusses how misalignment is detected, how its root cause is identified, and how vibration analysis is used to resolve the issue.
- Tony Planamento
- AME Solutions
Two Minute Tips
How Vibration Analysis Prevented a Catastrophic Failure
In a recent vibration analysis of a paper machine’s drying cylinder, we identified a 22238 C4 bearing on the drive side in an advanced stage of wear. In the first month of data collection, the overall acceleration level was already at 1.9 Gs, rising to 3.78 Gs the following month. Based on this data, we recommended an intervention during the next scheduled shutdown.
- Felipe Shishito
- Abecom
Two Minute Tips
Steam Turbine Governor Valve Failure: A Case Study from Singapore Refining Company
At the Asia Turbomachinery & Pump Symposium 2018, Vasanth Bhat and Thangavel Suthan from Singapore Refining Company (SRC) presented a compelling case study on the failure of a steam turbine governor valve in their Wet Gas Compressor (WGC) unit. This critical asset, driven by a four-stage back pressure turbine, experienced two major failures in the main valve stem of the steam inlet valve, leading to significant operational challenges.
- Khalid Farooq Khattak
- Fauji Fertilizer Company Limited
Two Minute Tips
What Is the Difference Between “Vibration Isolators” and “Shock Absorbers”?
This article will discuss vibration isolators, which are applied in many situations to achieve vibration isolation. This brings us back to a common question: is a vibration isolator the same as a shock isolator or a shock absorber? It also explores whether the purpose of vibration isolation is best described as a combination of isolation and shock absorption, or as vibration isolation and general isolation.
- Bor-Tsuen Wang
- National Pingtung University of Science and Technology
Two Minute Tips
Mounting a Triaxial MEMS Accelerometer
When many people think of a MEMS accelerometer, they think of a MEMS chip. This 2-minute tip will not address MEMS accelerometer chips, which require a pick-n-place machine and soldering to install onto a circuit board and then connection to an output mechanism. We’re going to address mounting an industrial MEMS triaxial accelerometer sensor to achieve the optimal measurement range and accurate readings.
- Peter Eitnier
- Wilcoxon Sensing Technologies
Two Minute Tips
Crest Factor in Vibration Analysis
The Crest Factor (CF) is a fundamental metric in vibration analysis, defined as the ratio of the peak amplitude of a time waveform to its root mean square (RMS) value This dimensionless ratio serves as an indicator of the severity of transient or impulsive events in a vibration signal.
- Muhammad Muneeb Babar
- Al Jouf Cement Company
Two Minute Tips
What is Resonance?
Resonance is a term that is familiar to everyone, but what is the phenomenon of resonance and what is the cause of resonance? Also, what is the "resonance frequency" that people often talk about?
- Bor-Tsuen Wang
- National Pingtung University of Science and Technology
Join Preston Johnson for a webinar on Hybrid-AI Predictive Maintenance for Industrial Equipment, where he will explore how physics-based failure-mode models and data-driven AI can be combined into an explainable hybrid approach, giving your team the tools to detect more failure modes earlier, prioritize evidence-backed diagnoses, and move from alerts to confident, prescriptive action.
Tuesday, November 17, 2026 | 2:00pm-3:00pm ET
